Namespace CTRE.Phoenix6.Controls

Request coast neutral output of actuator. The bridge is disabled and the rotor is allowed to coast.

Animation that gradually lights the entire LED strip one LED at a time.

Request a specified motor duty cycle with a differential position closed-loop.

This control mode will output a proportion of the supplied voltage which is supplied by the user. It will also set the motor's differential position setpoint to the specified position.

DifferentialFollower

Follow the differential motor output of another Talon.

If Talon is in torque control, the differential torque is copied - which will increase the total torque applied. If Talon is in duty cycle output control, the differential duty cycle is matched. If Talon is in voltage output control, the differential motor voltage is matched. Motor direction either matches leader's configured direction or opposes it based on the MotorAlignment.

The leader must enable its DifferentialOutput status signal. The update rate of the status signal determines the update rate of the follower's output and should be no slower than 20 Hz.

DifferentialMotionMagicDutyCycle

Requests Motion Magic® to target a final position using a motion profile, and PID to a differential position setpoint.

Motion Magic® produces a motion profile in real-time while attempting to honor the Cruise Velocity, Acceleration, and (optional) Jerk specified via the Motion Magic® configuration values. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

DifferentialMotionMagicExpoDutyCycle

Requests Motion Magic® to target a final position using an exponential motion profile, and PID to a differential position setpoint.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the Cruise Velocity (optional) and the mechanism kV and kA, specified via the Motion Magic® configuration values. Note that unlike the slot gains, the Expo_kV and Expo_kA configs are always in output units of Volts.

Setting Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

DifferentialMotionMagicExpoVoltage

Requests Motion Magic® to target a final position using an exponential motion profile, and PID to a differential position setpoint.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the Cruise Velocity (optional) and the mechanism kV and kA, specified via the Motion Magic® configuration values. Note that unlike the slot gains, the Expo_kV and Expo_kA configs are always in output units of Volts.

Setting Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

DifferentialMotionMagicVelocityDutyCycle

Requests Motion Magic® to target a final velocity using a motion profile, and PID to a differential position setpoint. This allows smooth transitions between velocity set points.

Motion Magic® Velocity produces a motion profile in real-time while attempting to honor the specified Acceleration and (optional) Jerk. This control mode does not use the CruiseVelocity, Expo_kV, or Expo_kA configs.

Acceleration and jerk are specified in the Motion Magic® persistent configuration values. If Jerk is set to zero, Motion Magic® will produce a trapezoidal acceleration profile.

Target velocity can also be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

DifferentialMotionMagicVelocityVoltage

Requests Motion Magic® to target a final velocity using a motion profile, and PID to a differential position setpoint. This allows smooth transitions between velocity set points.

Motion Magic® Velocity produces a motion profile in real-time while attempting to honor the specified Acceleration and (optional) Jerk. This control mode does not use the CruiseVelocity, Expo_kV, or Expo_kA configs.

Acceleration and jerk are specified in the Motion Magic® persistent configuration values. If Jerk is set to zero, Motion Magic® will produce a trapezoidal acceleration profile.

Target velocity can also be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

DifferentialMotionMagicVoltage

Requests Motion Magic® to target a final position using a motion profile, and PID to a differential position setpoint.

Motion Magic® produces a motion profile in real-time while attempting to honor the Cruise Velocity, Acceleration, and (optional) Jerk specified via the Motion Magic® configuration values. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

DifferentialPositionDutyCycle

Request PID to target position with a differential position setpoint.

This control mode will set the motor's position setpoint to the position specified by the user. It will also set the motor's differential position setpoint to the specified position.

DifferentialPositionVoltage

Request PID to target position with a differential position setpoint

This control mode will set the motor's position setpoint to the position specified by the user. It will also set the motor's differential position setpoint to the specified position.

DifferentialStrictFollower

Follow the differential motor output of another Talon while ignoring the leader's invert setting.

If Talon is in torque control, the differential torque is copied - which will increase the total torque applied. If Talon is in duty cycle output control, the differential duty cycle is matched. If Talon is in voltage output control, the differential motor voltage is matched. Motor direction is strictly determined by the configured invert and not the leader. If you want motor direction to match or oppose the leader, use DifferentialFollower instead.

The leader must enable its DifferentialOutput status signal. The update rate of the status signal determines the update rate of the follower's output and should be no slower than 20 Hz.

DifferentialVelocityDutyCycle

Request PID to target velocity with a differential position setpoint.

This control mode will set the motor's velocity setpoint to the velocity specified by the user. It will also set the motor's differential position setpoint to the specified position.

DifferentialVelocityVoltage

Request PID to target velocity with a differential position setpoint.

This control mode will set the motor's velocity setpoint to the velocity specified by the user. It will also set the motor's differential position setpoint to the specified position.

DifferentialVoltage

Request a specified voltage with a differential position closed-loop.

This control mode will attempt to apply the specified voltage to the motor. If the supply voltage is below the requested voltage, the motor controller will output the supply voltage. It will also set the motor's differential position setpoint to the specified position.

DutyCycleOut

Request a specified motor duty cycle.

This control mode will output a proportion of the supplied voltage which is supplied by the user.

DynamicMotionMagicDutyCycle

Requires Phoenix Pro and CANivore; Requests Motion Magic® to target a final position using a motion profile. This dynamic request allows runtime changes to Cruise Velocity, Acceleration, and (optional) Jerk. Users can optionally provide a duty cycle feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the specified Cruise Velocity, Acceleration, and (optional) Jerk. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

DynamicMotionMagicExpoDutyCycle

Requires Phoenix Pro and CANivore; Requests Motion Magic® Expo to target a final position using an exponential motion profile. This dynamic request allows runtime changes to the profile kV, kA, and (optional) Cruise Velocity. Users can optionally provide a duty cycle feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the specified Cruise Velocity (optional) and the mechanism kV and kA. Note that unlike the slot gains, the Expo_kV and Expo_kA parameters are always in output units of Volts.

Setting the Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

DynamicMotionMagicExpoTorqueCurrentFOC

Requires Phoenix Pro and CANivore; Requests Motion Magic® Expo to target a final position using an exponential motion profile. This dynamic request allows runtime changes to the profile kV, kA, and (optional) Cruise Velocity. Users can optionally provide a torque current feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the specified Cruise Velocity (optional) and the mechanism kV and kA. Note that unlike the slot gains, the Expo_kV and Expo_kA parameters are always in output units of Volts.

Setting the Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is based on torque current, so relevant closed-loop gains will use Amperes for the numerator.

DynamicMotionMagicExpoVoltage

Requires Phoenix Pro and CANivore; Requests Motion Magic® Expo to target a final position using an exponential motion profile. This dynamic request allows runtime changes to the profile kV, kA, and (optional) Cruise Velocity. Users can optionally provide a voltage feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the specified Cruise Velocity (optional) and the mechanism kV and kA. Note that unlike the slot gains, the Expo_kV and Expo_kA parameters are always in output units of Volts.

Setting the Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

DynamicMotionMagicTorqueCurrentFOC

Requires Phoenix Pro and CANivore; Requests Motion Magic® to target a final position using a motion profile. This dynamic request allows runtime changes to Cruise Velocity, Acceleration, and (optional) Jerk. Users can optionally provide a torque current feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the specified Cruise Velocity, Acceleration, and (optional) Jerk. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is based on torque current, so relevant closed-loop gains will use Amperes for the numerator.

DynamicMotionMagicVoltage

Requires Phoenix Pro and CANivore; Requests Motion Magic® to target a final position using a motion profile. This dynamic request allows runtime changes to Cruise Velocity, Acceleration, and (optional) Jerk. Users can optionally provide a voltage feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the specified Cruise Velocity, Acceleration, and (optional) Jerk. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

EmptyAnimation

An empty animation, clearing any animation in the specified slot.

EmptyControl

Generic Empty Control class used to do nothing.

FireAnimation

Animation that looks similar to a flame flickering.

Follower

Follow the motor output of another Talon.

If Talon is in torque control, the torque is copied - which will increase the total torque applied. If Talon is in duty cycle output control, the duty cycle is matched. If Talon is in voltage output control, the motor voltage is matched. Motor direction either matches the leader's configured direction or opposes it based on the MotorAlignment.

The leader must enable the status signal corresponding to its control output type (DutyCycle, MotorVoltage, TorqueCurrent). The update rate of the status signal determines the update rate of the follower's output and should be no slower than 20 Hz.

LarsonAnimation

Animation that bounces a pocket of light across the LED strip.

ModulateVBatOut

Modulates the CANdle VBat output to the specified duty cycle. This can be used to control a single-color LED strip.

Note that CANdleFeaturesConfigs.VBatOutputMode must be set to VBatOutputModeValue.Modulated.

MotionMagicDutyCycle

Requests Motion Magic® to target a final position using a motion profile. Users can optionally provide a duty cycle feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the Cruise Velocity, Acceleration, and (optional) Jerk specified via the Motion Magic® configuration values. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

MotionMagicExpoDutyCycle

Requests Motion Magic® to target a final position using an exponential motion profile. Users can optionally provide a duty cycle feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the Cruise Velocity (optional) and the mechanism kV and kA, specified via the Motion Magic® configuration values. Note that unlike the slot gains, the Expo_kV and Expo_kA configs are always in output units of Volts.

Setting Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

MotionMagicExpoTorqueCurrentFOC

Requires Phoenix Pro; Requests Motion Magic® to target a final position using an exponential motion profile. Users can optionally provide a torque current feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the Cruise Velocity (optional) and the mechanism kV and kA, specified via the Motion Magic® configuration values. Note that unlike the slot gains, the Expo_kV and Expo_kA configs are always in output units of Volts.

Setting Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is based on torque current, so relevant closed-loop gains will use Amperes for the numerator.

MotionMagicExpoVoltage

Requests Motion Magic® to target a final position using an exponential motion profile. Users can optionally provide a voltage feedforward.

Motion Magic® Expo produces a motion profile in real-time while attempting to honor the Cruise Velocity (optional) and the mechanism kV and kA, specified via the Motion Magic® configuration values. Note that unlike the slot gains, the Expo_kV and Expo_kA configs are always in output units of Volts.

Setting Cruise Velocity to 0 will allow the profile to run to the max possible velocity based on Expo_kV. This control mode does not use the Acceleration or Jerk configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

MotionMagicTorqueCurrentFOC

Requires Phoenix Pro; Requests Motion Magic® to target a final position using a motion profile. Users can optionally provide a torque current feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the Cruise Velocity, Acceleration, and (optional) Jerk specified via the Motion Magic® configuration values. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is based on torque current, so relevant closed-loop gains will use Amperes for the numerator.

MotionMagicVelocityDutyCycle

Requests Motion Magic® to target a final velocity using a motion profile. This allows smooth transitions between velocity set points. Users can optionally provide a duty cycle feedforward.

Motion Magic® Velocity produces a motion profile in real-time while attempting to honor the specified Acceleration and (optional) Jerk. This control mode does not use the CruiseVelocity, Expo_kV, or Expo_kA configs.

If the specified acceleration is zero, the Acceleration under Motion Magic® configuration parameter is used instead. This allows for runtime adjustment of acceleration for advanced users. Jerk is also specified in the Motion Magic® persistent configuration values. If Jerk is set to zero, Motion Magic® will produce a trapezoidal acceleration profile.

Target velocity can also be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is duty cycle based, so relevant closed-loop gains will use fractional duty cycle for the numerator: +1.0 represents full forward output.

MotionMagicVelocityTorqueCurrentFOC

Requests Motion Magic® to target a final velocity using a motion profile. This allows smooth transitions between velocity set points. Users can optionally provide a torque feedforward.

Motion Magic® Velocity produces a motion profile in real-time while attempting to honor the specified Acceleration and (optional) Jerk. This control mode does not use the CruiseVelocity, Expo_kV, or Expo_kA configs.

If the specified acceleration is zero, the Acceleration under Motion Magic® configuration parameter is used instead. This allows for runtime adjustment of acceleration for advanced users. Jerk is also specified in the Motion Magic® persistent configuration values. If Jerk is set to zero, Motion Magic® will produce a trapezoidal acceleration profile.

Target velocity can also be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is based on torque current, so relevant closed-loop gains will use Amperes for the numerator.

MotionMagicVelocityVoltage

Requests Motion Magic® to target a final velocity using a motion profile. This allows smooth transitions between velocity set points. Users can optionally provide a voltage feedforward.

Motion Magic® Velocity produces a motion profile in real-time while attempting to honor the specified Acceleration and (optional) Jerk. This control mode does not use the CruiseVelocity, Expo_kV, or Expo_kA configs.

If the specified acceleration is zero, the Acceleration under Motion Magic® configuration parameter is used instead. This allows for runtime adjustment of acceleration for advanced users. Jerk is also specified in the Motion Magic® persistent configuration values. If Jerk is set to zero, Motion Magic® will produce a trapezoidal acceleration profile.

Target velocity can also be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

MotionMagicVoltage

Requests Motion Magic® to target a final position using a motion profile. Users can optionally provide a voltage feedforward.

Motion Magic® produces a motion profile in real-time while attempting to honor the Cruise Velocity, Acceleration, and (optional) Jerk specified via the Motion Magic® configuration values. This control mode does not use the Expo_kV or Expo_kA configs.

Target position can be changed on-the-fly and Motion Magic® will do its best to adjust the profile. This control mode is voltage-based, so relevant closed-loop gains will use Volts for the numerator.

MusicTone

Plays a single tone at the user specified frequency.

NeutralOut

Request neutral output of actuator. The applied brake type is determined by the NeutralMode configuration.

PositionDutyCycle

Request PID to target position with duty cycle feedforward.

This control mode will set the motor's position setpoint to the position specified by the user. In addition, it will apply an additional duty cycle as an arbitrary feedforward value.

PositionTorqueCurrentFOC

Requires Phoenix Pro; Request PID to target position with torque current feedforward.

This control mode will set the motor's position setpoint to the position specified by the user. In addition, it will apply an additional torque current as an arbitrary feedforward value.

PositionVoltage

Request PID to target position with voltage feedforward

This control mode will set the motor's position setpoint to the position specified by the user. In addition, it will apply an additional voltage as an arbitrary feedforward value.

RainbowAnimation

Animation that creates a rainbow throughout all the LEDs.

RgbFadeAnimation

Animation that fades all the LEDs of a strip simultaneously between Red, Green, and Blue.

SingleFadeAnimation

Animation that fades into and out of a specified color.

SolidColor

Sets LEDs to a solid color.

StaticBrake

Applies full neutral-brake by shorting motor leads together.

StrictFollower

Follow the motor output of another Talon while ignoring the leader's invert setting.

If Talon is in torque control, the torque is copied - which will increase the total torque applied. If Talon is in duty cycle output control, the duty cycle is matched. If Talon is in voltage output control, the motor voltage is matched. Motor direction is strictly determined by the configured invert and not the leader. If you want motor direction to match or oppose the leader, use Follower instead.

The leader must enable the status signal corresponding to its control output type (DutyCycle, MotorVoltage, TorqueCurrent). The update rate of the status signal determines the update rate of the follower's output and should be no slower than 20 Hz.

StrobeAnimation

Animation that strobes the LEDs a specified color.

TorqueCurrentFOC

Requires Phoenix Pro; Request a specified motor current (field oriented control).

This control request will drive the motor to the requested motor (stator) current value. This leverages field oriented control (FOC), which means greater peak power than what is documented. This scales to torque based on Motor's kT constant.

TwinkleAnimation

Animation that randomly turns LEDs on and off to a certain color.

TwinkleOffAnimation

Animation that randomly turns on LEDs until it reaches the maximum count, and then turns them all off.

VelocityDutyCycle

Request PID to target velocity with duty cycle feedforward.

This control mode will set the motor's velocity setpoint to the velocity specified by the user. In addition, it will apply an additional voltage as an arbitrary feedforward value.

VelocityTorqueCurrentFOC

Requires Phoenix Pro; Request PID to target velocity with torque current feedforward.

This control mode will set the motor's velocity setpoint to the velocity specified by the user. In addition, it will apply an additional torque current as an arbitrary feedforward value.

VelocityVoltage

Request PID to target velocity with voltage feedforward.

This control mode will set the motor's velocity setpoint to the velocity specified by the user. In addition, it will apply an additional voltage as an arbitrary feedforward value.

VoltageOut

Request a specified voltage.

This control mode will attempt to apply the specified voltage to the motor. If the supply voltage is below the requested voltage, the motor controller will output the supply voltage.

ControlRequest

Common interface implemented by all control requests.

Table of Contents

Namespace CTRE.Phoenix6.Controls

Classes

Interfaces